• IG-10

    Article No. 714405

    IG-10 Impregnation Primer IT

    Liquid wood preservative on a solvent base with preventive efficacy against blue stain, soft rot, insects and termites

    Colour: clear | 7144
    Colour: clear | 7144
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Hazard warnings

    • Use biocides safely. Always read the label and product information before using!

    Product specifications

    Binder Mixture of alkydic resins
    Density (20°C) Approx. 0.82 g/cm³
    Odour Solvent-like, odourless after drying
    Viscosity (20 °C) Approx. 25 s im a 3 mm flow cup according to ISO 2431

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Wood which is not in ground contact, in accordance with DIN EN 335-1, use classes 2 and 3
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Load-bearing wood elements under roofs (e.g. trusses)
    • Dimensionally stable wood building elements (when used as a primer only): e.g. windows and doors
    • Pre-treatment under translucent or opaque coatings

    Properties

    • Solvent-based
    • Protection against rot, blue stain and termites
    • Resistant to swelling, regulates moisture
    • Impregnated wood is suitable for all follow-up coatings
    • Economical thanks to the low application rate
    • Preparation
      • Substrate requirements

        The substrate must be clean, dust-free and dry.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Stir before use
      • By brush / Dipping / Flow coating/ Spraying tunnel
      • Application requirements

        Temperature of material, surroundings and substrate: min. +5 °C - max. +30 °C.

      • Stir well.

        Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 24 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      • Drying

        Can be overcoated after approx. 24 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

        After drying, the treated wood can be finished with acwater-based or solvent-based coating system.

        If a water-based finish is used, overnight drying is required.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / Dipping / Flow coating/ Spraying tunnel
      • Paintbrush with natural bristles, flat brush, dipping tank, spraying tunnel

      • Clean tools immediately after use with V 101 Thinner.
        Dispose of the remains from cleaning properly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.

    • Usage
      • Total application/absorption rate 150 ml Total / m²
      • Preventive protection against blue stain, soft rot, insects and termites at 150 ml/m²

    • General information
      • According to the current state of the art (this includes DIN 68800-1 and -3 in Germany), wood preservation measures must also be planned for non-load-bearing wooden elements in good time and with due care, with the agreement of all parties involved in the construction (architect, developer, builder) and in compliance with the legal requirements and the conditions on site. The use of biocidal (“chemical”) wood preservatives should therefore always be indicated in suitable fashion prior to sale, or must be agreed in advance with the client in writing. Failure to comply with this requirement may result in country-specific or contract-specific conflicts with legal requirements, standards or certification systems. The Remmers Technical Service would be happy to discuss the matter and provide you with a template agreement for the use of a biocidal (“chemical”) wood preservative on the wooden elements being used.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

        European waste code 03 02 99 wood preservatives not otherwise specified

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.