• Induline OW-815
  • Induline OW-815
    • Induline OW-815
    • Induline OW-815

    Article No. 345105

    Induline OW-815

    Water-based surface protection for decking boards

    Colour: clear | 3451
    Colour: clear | 3451
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    Binder Acrylate dispersion
    Density (20°C) Approx. 1.03 g/cm³
    Odour Characteristic
    Degree of gloss Matt
    Runout time s (20° C, DIN 4) Approx. 15

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • for wood garden furniture
    • For professional users only
    • For use on exterior wood
    • Building elements with no or limited dimensional stability
    • Wood decks and garden furniture

    Properties

    • Water-based
    • Long life thanks to special UV absorbers and lignin stabilisers
    • Weatherproof and moisture-regulating
    • Film preserver protects against microbial damage
    • Quick drying
    • Does not flake
    • Very good adhesion to the substrate
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Sand off or strip any old coatings and clean the surface of the wood.

        Thoroughly wash down resin-rich and oily woods with V 101 Thinner immediately before coating.

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C
      • Stir before use
      • Automatic vacuum impregnation
      • Board coating machine/ brushing machine
      • Spraying only in closed facilities
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C

      • Stir well, including during application or after a break in work.

        Apply a second coat once the first has dried.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

        Prior to full application, please apply a test coat to a sample area under practical conditions using the desired system, then test or examine the surface properties.

        Rainfall may cause water soluble substances to bleed from wood that is rich in such substances, e.g. oak, red cedar, afzelia, redwood, etc. This may lead to the discolouration of light-coloured masonry or render.

        Regular reapplications are required in areas exposed to weathering.

      • Drying

        Dust-dry: after approx. 2 hours
        Overcoating: after approx. 4 hours
        Full load-bearing capacity: after approx. 24 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Automatic vacuum impregnation
      • Board coating machine/ brushing machine
      • Spraying only in closed facilities
      • VACUMAT® vacuum machine, spraying equipment, board coating machine

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 60 ml - 80 ml / m² per layer applied
      • 60 - 80 ml/m² per coat depending on the absorbency of the wood

      • Apply thinly and in no more than two coats.

        Remove or smooth out any excess material (especially in tongues and grooves) immediately.

    • General information
      • On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.