• Induline LW-722 [eco]
  • Induline LW-722 [eco]
    eco
    Product
    • Induline LW-722 [eco]
    • Induline LW-722 [eco]

    Article No. 510005

    Induline LW-722 [eco]

    Resource-conserving, water-based, transparent intermediate and finishing coat for wood-aluminium building elements

    Variant
    Induline LW-722/10 [eco] dull matt
    Colour: clear | 5100
    Colour: clear | 5100
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    On delivery

    Binder Acrylate
    Density (20°C) Approx. 1.03 g/cm³
    Odour Characteristic
    Degree of gloss Dull matt
    Viscosity 2400 - 2800 mPa*s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • for dimensionally stable elements
    • For professional users only
    • Soft and hard woods
    • Dimensionally stable wood/aluminium building elements: e.g. wood/aluminium windows and doors
    • Protected constructions without direct outdoor exposure
    • Intermediate and finishing coats
    • Single coat and multi-coat procedure

    Properties

    • Water-based
    • This product is based on a balanced-biomass binding agent. 100% of the fossil raw materials have been replaced with renewable raw materials for the production of the binding agent.
    • Good flow properties
    • Block resistant (in accordance with Code of Practice HO.03)
    • UV-resistant and colourfast
    • Reduces grain emphasis and yellowing of wood substrate
    • Pleasant feel
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.

        If necessary, protect parapet joints with Induline V-Joint Protection or Induline AF-920.

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Stir before use
      • Airless/airmix spraying
      • Application requirements

        Temperature of the object, air and material: +15 °C to +30 °C.

      • The values given are based on undiluted material. The best spraying pattern is achieved if the material has a temperature of 15-20 °C.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

        Do not use in direct sunlight or at temperatures below +15 °C or above +30 °C.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        To prevent any substances in the wood from becoming active, forced drying should be carried out.

        The clear colour version of the product is not suited for use on exterior surfaces that are directly exposed to weather.

        The system finder on our website www.remmers.com contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

      • Drying

        Dust-dry: after approx. 1 hour Can be sanded and overcoated: after approx. 4 hours (at 23 °C and 50% RH) If forced drying is used, can be sanded and overcoated: after approx. 20 minutes flash-off zone (at approx. 20 °C and 65 - 75% RH)/75 minutes drying phase (approx. 45 °C, 1 m/s air circulation)/20 minutes cooling phase

      • Thinning

        With water if required (max. 5%).

    • Working tools / cleaning
      • Airless/airmix spraying
      • Manual spray guns, automatic spraying equipment

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 125 ml - 225 ml / m² per layer applied
      • Approx. 125-225 ml/m² (plus spraying losses) (corresponds to a wet film thickness of 125-225 µm and dry film thickness of 40-80 µm)

    • General information
      • Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Only use sealing profiles that are free of plasticisers.

        This product can be used with Induline Mix & Go to produce an easy-to-apply lacquer for reconditioning and repair work.

        Wood is subjected to great climatic and environmental stresses when outdoors. The coat is susceptible to the processes of natural ageing, wear and decomposition. Decomposition takes place at different speeds, depending on the stress (weak, average, strong) placed on the wood building element. Weathering stages may vary according to the part or element affected. To give wood the longest and best possible protection it is advisable to examine surfaces every year. Any damage found should be addressed immediately after cleaning.

        For cleaning and care, we recommend the care set for windows (2745)

        We recommend that repairs be carried out using Aqua HSL-35/m Professional Wood Protection Stain 3in1* and Aqua DSL-55 High Build Stain PU. (*Use biocides safely. Always read the label and product information before use.)

        Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.