Article No. 182685
Durable, single-component wood sealer for a natural look and two-time application
Downloads & documents
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Wood in living areas
- Furniture and interior finishing work
- Wooden floors and stairs
- Tables and worktops
- Interior finishing of ships
- For bath and sauna elements
- No removal of excess
- Cork floors
- Bamboo components
- Resistant to abrasion and scratches
- Resistant to chemicals: DIN 68861, 1B
- Very low tendency to shine
- Natural look and feel
- Fire resistant
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
Final wood sanding no finer than P 180
Thoroughly remove any dirt, grease and non-adhering old coatings.
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.
If you wish to add colour, prime with Decorative Wax Stain or OB-008.
If applying a subsequent coating using a roller: intermediate drying time min. 24 hours.
When sealing old parquet flooring, end-grain wood parquet and installation patterns with the wood grain running in different directions, we recommend pre-treating with OB-008 clear and leaving to dry for at least 48 hours in order to ensure that the substrate is thoroughly saturated and absorbs the material evenly.
Temperature of the material, air and substrate: from min. +15°C to max. +25°C
For better wetting of the substrate and pores, we recommend applying the first coat as a slurry or with a roller.
Apply by spraying or with a roller.
Flow cup gun: nozzle: 1.6 - 1.8 mm; atomiser air pressure: max. 2 bar
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: max. 1 bar.
After drying and intermediate sanding (P 240 - 320), apply a second coat of the product.
Observe the waiting times between coats.
Seal opened containers well and use contents as soon as possible.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
For smoked oak and other exotic woods, Remmers Technical Service must be consulted prior to use and a trial area set up.
Owing to the high reactivity of the product, skin formation may occur. Please remove before stirring and sieve as a precaution.
Make sure the area is well ventilated when using indoors.
Dispose spray dust deposits regularly to avoid ignition of the spray dust.
Avoid ultra-fine material atomisation and excessive overspray.
Leave fresh spraying dust to dry before sweeping up.
The product itself is not self-igniting.
When sanding wooden surfaces that have been treated with the product, always wear respiratory protection (dust filter mask P2).
Risk of self-ignition (DGUV information brochure 209-046).
The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.
Dust-dry: after approx. 60 minutes Touch-dry: after approx. 3 hours Can be overcoated by spraying: after approx. 6 hours Can be overcoated using a roller: after approx. 14 hours Full loading capacity: after approx. 7 days
Practice values at +20 °C and 65% relative humidity.
Low temperatures and high humidity delay drying.
Drying is dependent on the type of wood and the absorbency of the substrate.
Ready to use
Working tools / cleaning
Short-pile (3-5 mm) velour or mohair roller, flow cup gun, airless/airmix spraying equipment, scraper
Clean tools immediately after use with V 101 Thinner.
Ensure that any residue from cleaning is disposed of correctly.
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
First coat: 70 ml/m² Second coat: 60 ml/m²
Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.
Use breathable materials when packing the coated wood building elements.
Dust and loose dirt on floors and stairs should be removed regularly using a soft broom or mop.
For maintenance (including partial maintenance on traffic areas subject to particular levels of wear), treat the cleaned surface with the product or with Hard Wax Oil in such a way that it blends in to produce a uniform finish.
If necessary, mop once a week with a slightly damp cloth, making sure to add Oiled Floor Care [eco] to the water used for mopping.
Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.