• Default Package Display_GB

    Article No. 26018425

    PUR Indu Color N

    2-component, solvent free, self leveling polyurethane coating

    260184 | PUR Indu Color N
    Size / Quantity

    Brochures and Catalogues


    Product specifications

    Density (20°C) 1500 kg/m³
    Compressive strength min. 25 N/mm²
    Adhesive pull strength min. 1,5 N/mm²
    Drying time min. 16 hours and max. 48 hours

    Once fully cured

    Shore D after 28 days 60
    Elongation at break (DIN 52455-A1) 100 - 110% DIN 53455

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on floors indoors
    • For professional users only
    • Seamless, wear resistant floor finish for several application areas
    • Examples of application areas are: education, healthcare, residences, offices and public buildings
    • For use Wood, Asphalt, Steel and concrete
    • Flexible for Mezzanine Structures
    • Waterproofing of Plant room floors


    • Tough coating
    • With static crack-bridging ability
    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Suitable for hand pallet trucks and forklift trucks
    • Physiologically harmless once fully cured
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The substrate must be dry.

        Suitable Remmers Epoxy primers or Epoxy scratch coats must be used on cement substrates.

        Refer to the current Technical Data Sheet for detailed information on the single products.

        Prime interior poured asphalt surfaces (AS-IC 10 or AS-IC 15) with PUR Uni Color.

        For works within the framework of the general building inspectorate approval, the substrates must correspond to the requirements of the approval and the system products mentioned therein must be used.

      • Preparations

        In the case of interior poured asphalt surfaces, take suitable measures to prepare the substrate, e.g. steel ball blasting or grinding with a diamond disc, in order to meet the requirements listed above.

        Then prime and/or level out with PUR Indu Color N.

    • Preparation
      • Mixing ratio comp. A 5: comp. B 1
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Application instructions
      • Drying time: can be worked over after 16 h
      • Drying

        The drying and curing times of the PUR Indu Color N, at a layer thickness of 2 mm are as follows:
        - recoatable : after 16 hours and a maximum within 48 hours at 20 °C
        - fully cured : after 7 days at 20 °C

    • Working tools / cleaning
      • PUR Indu Color N can be applied with:
        Toothed trowel, toothed scraper, rubber scraper, epoxy roller, suitable mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • In the original, unopened packaging, stored in a dry place between 5 °C and 25 °C, minimum 12 months.

        May not be stored or exposed to temperatures beneath 5 °C.

    • Usage
      • See application examples

    • Application examples
      • ApplicationLevel of filling with select mix 01/03Binder application rate [kg / m²]Mixture application rate [kg / m²]Toothed bladeApplication rate per mm layer thickness [kg / m²]
        Coating <mmunfilled0.5 0.5 Roller1.40
        Filled coating1: 0.5min 1.7 kg / m²min 2.5 kg / m²No. 551.50

      • Priming

        Pour the material liberally onto the poured asphalt surface. Spread using a suitable tool, e.g. a rubber scraper, then roll using an epoxy roller.

        approx. 0.4 kg/m² binder (depending on the substrate)

      • Levelling layer/scratch coat

        Pour the material filled up to 1 : 0.3 parts by weight onto the prepared surface and spread using a suitable trowel.

        (see table)

      • Coating

        Pour the material onto the surface and spread evenly with a rubber scraper and epoxy roller.

        The application rate depends on the substrate, temperature, required coating thickness, and optical requirements.

        (see table)

      • Filled coating

        Pour the material filled with Selectmix 01/03 on the previously prepared surface and distribute with a suitable toothed trowel/spreader and, if needed, roll over with a spiked roller.

        The degree of filling must be chosen depending on substrate, temperature and required layer thickness.

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Owing to the tendency to yellow, the possible colour deviations, and the reaction to soiling, it is highly recommended to apply a suitable coloured Remmers seal coat.

        Special colours, low layer thickness or differing sand fractions as well as lower temperatures can reduce the maximum degree of filling of the material and possibly affect the visual appearance of the surface.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Abrasive mechanical loads leave traces of wear.

        Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.