• SP Level

    Article No. 040120

    SP Levell

    Salt-retaining, WTA-compliant pore undercoat render in the restoration render system for masonry exposed to moisture and salt

    Variant
    0401 | grey (inherent colour)
    Size / Quantity

    Product specifications

    Compressive strength CS III (3.5 - 7.5 N/mm²)
    External surveillance GG-Cert + WTA
    Maximum grain size 2 mm
    aggregate as per DIN EN 13139
    Capillary water absorption w24 > 1.0 kg/m²
    Porosity > 45 vol.%
    Layer thickness Single layer 10 to 40 mm
    Bulk density Approx. 1.0 kg/dm³
    Water requirement Approx. 6.5 l/20 kg
    Water vapour diffusion resistance coefficient µ ≤ 15
    Water penetration depth After 24 h > 5 mm
    Reaction to fire class A1

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Wall surfaces and masonry subjected to moisture and damaging salts
    • Old buildings, cellars and facades
    • Removal of salt and reduction of moisture
    • Condensate buffer and protective layer on internal seals

    Properties

    • High salt storing capacity
    • Porosity > 45 vol%
    • High sulphate resistance and low active alkali content (SR/NA)
    • Enables water vapour diffusion
    • Capillary-active
    • Single-layer application thickness from 10 to 40 mm
    • Machine workable
    • Preparation
      • Substrate requirements

        Clean, dust-free and capable of supporting a load.

      • Preparations

        Remove render, paint layers and coatings at least 80 cm above the damaged area.

        Chase out friable joints to a depth of at least 2 cm.

        Pre-wet absorbent substrates so that they are slightly damp.

        Substrate: absorbent with low strength

        Apply SP Prep as a bonding layer in a network pattern (covering 50-70% of the surface) at a layer thickness of max. 5 mm.

        Alternative: apply SP Levell as a scratch coat (contact layer).

        Substrate: weakly absorbent

        Apply SP Prep so that it fully covers the surface (100%) at a layer thickness of max. 5 mm.

        Alternative: apply SP Levell as a scratch coat (contact layer).

        Substrate: mineral waterproofing slurry

        Apply SP Prep over the entire surface area (100%) of the last slurry layer, wet-on-wet, as a bonding layer with a maximum coating thickness of 5 mm.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Mortar cover / Filling knife / Trowel application / Application by spraying
      • One-layer

        Apply product using a suitable tool or machine.

         

        Two-layer

        Roughen the first layer with a render comb.

        Apply second layer once sufficiently dry.

        Level off surface with a long float.

        Use a render comb to roughen horizontally in preparation for the next layer of render after setting.

        Alternative: Once the surface is sufficiently dry, use a grated scraper to prepare it for subsequent coatings.

         

    • Application instructions
      • Once it has hardened, mortar must not be made workable again by adding either water or more wet mortar.

        Protect wet mortar surfaces against frost, rain and drying out too quickly for at least 4 days.

        Hairline/shrinkage cracks are safe and are not cause for complaint as they do not impair the properties of the mortar.

        To ensure that the renovation is successful, the relevant drying conditions according to WTA Code of Practice 2-9-20/D must be met.

        Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.

        When processing in machines, the product-specific data, such as strength, air void content, etc. might change.

    • Working tools / cleaning
      • Mortar cover / Filling knife / Trowel application / Application by spraying
      • Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • Approx. 9.5 kg / cm thick layer / m²
      • Approx. 9.5 kg/m²/cm layer thickness

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • May contain traces of pyrite (iron sulphide).

        Do not use on gypsum-based substrates.

        The mixing water must be of drinking water quality.

        Low chromate content in accordance with Directive 2003/53/EC.

        Always set up a trial area/trial areas first.

        The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

        Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products