• Pourable PUR 2K
  • Pourable PUR 2K
  • Pourable PUR 2K
    • Pourable PUR 2K
    • Pourable PUR 2K
    • Pourable PUR 2K

    Article No. 755004

    Pourable PUR 2K

    Self-levelling, 2-component joint sealing compound on a PUR base

    Colour: grey | 7550
    Size / Quantity

    Note: This container size is being phased out and is only available to a limited extent.

    Product specifications

    Density (20°C) 1.35 g/cm³
    Colour grey (roughly corresponds to RAL 7037)
    Pot life 60 minutes in standard climate

    Component A

    Density (20°C) Approx. 1.4 g/ml

    Component B

    Density (20°C) Approx. 1.1 g/ml


    Density (20°C) Approx. 1.3 g/ml

    Once fully cured

    Elongation at break
    (DIN EN ISO 8339)
    Approx. 80 %
    Volume loss
    (DIN EN ISO 10563)
    Approx. 3 %

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on floors indoors and outdoors
    • Sealing horizontal construction and expansion joints
    • Surfaces with high wear loads such as floor joints in screed and concrete, joints in halls, warehouses, loading areas, terraces, etc.


    • Especially high wear resistance
    • Resistance against abrasive loads
    • Preparation
      • Substrate requirements

        The sides of the joints must be load-bearing, dry, clean and free of grease, metals must be bare.

      • Preparations

        Prime the joint edges with a suitable Remmers Primer.

        Fill deep joints with round cords.

    • Preparation
      • Mixing ratio comp. A 95.1 : comp. B 4.9
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 35 °C
      • Pot life 60 min
      • After mixing, pour the material into the joint with a pouring aid.

    • Application instructions
      • Uncontrolled material flow must be prevented by suitable measures.

        The stability of the material can be increased by adding a suitable thixotropic agent (e.g. WHG TX).

        Protect the material from weathering for at least 24 hours after application.

    • Working tools / cleaning
      • Suitable mixing device, pouring aid

        Clean tools while fresh with V 101. After setting, the material can only be removed by mechanical means. If necessary, swell first with V 101.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 135 g/running metre for a 1 cm² joint cross-section

    • General information
      • Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        Always set up a trial area/trial areas first.

        After approx. 3 days chemically and mechanically resistant.

        Bitumen intolerant.

        Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

    Possible system products