• SP Top SR

    Article No. 041620

    SP Top SR

    WTA-compliant restoration render for damp and salt-loaded masonry with especially high sulphate resistance

    Colour: grey (inherent colour) | 0416
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Plinth areas with and without waterproofing
    • Substrates contaminated with high levels of damaging salts
    • Repair, renovation and restoration of old, damp and salt-loaded masonry

    Properties

    • High sulphate resistance and low active alkali content (SR/NA)
    • High compressive strength
    • Enables water vapour diffusion
    • Single-layer application thickness up to 30 mm
    • Machine workable
    • Preparation
      • Substrate requirements

        Clean, dust-free and capable of supporting a load.

      • Preparations

        Remove render, paint layers and coatings at least 80 cm above the damaged area.

        Chase out friable joints to a depth of at least 2 cm.

        Pre-wet absorbent substrates so that they are slightly damp.

        Substrate: absorbent with low strength

        Apply SP Prep or SP Prep rapid as a bonding layer in net form (covering area 50-70%) with max. 5 mm layer thickness.

        Alternative: apply SP Top SR as a scratch coat (contact layer).

        Substrate: weakly absorbent

        Apply SP Prep or SP Prep rapid at full coverage (100%) with max. 5 mm layer thickness.

        Alternative: apply SP Top SR as a scratch coat (contact layer).

        Substrate: mineral waterproofing slurry

        Apply SP Prep as a full-coverage bonding layer on the last slurry layer wet-on-wet.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Mortar cover / Filling knife / Trowel application / Application by spraying
      • Drying time: can be worked over after 60 minutes
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • One-layer

        Apply product using a suitable tool or machine.

         

        Two-layer

        Roughen the first layer with a render comb.

        Apply second layer once sufficiently dry.

        Alternatively, apply the total layer thickness in 2 coats, wet on wet, embedding reinforcement fabric (Tex 6.5/100).

        Ensure that fabric sheets overlap by at least 10 cm.

         

        Level off surface with a long float.

        Finish the surface once set.

        Prepare the surface for subsequent layers with a grated scraper after sufficient setting.

        Pre-wet hydrophobic surfaces with detensioned water so that they are slightly damp before applying further render coats.

         

    • Application instructions
      • Once it has hardened, mortar must not be made workable again by adding either water or more wet mortar.

        On critical substrates (highly uneven, fissured, mixed masonry) we recommend incorporating the reinforcement fabric in the upper third of the restoration render.

        Apply additional diagonal reinforcement to the edges of building openings.

        Protect wet mortar surfaces against frost, rain and drying out too quickly for at least 4 days.

        Hairline/shrinkage cracks are safe and are not cause for complaint as they do not impair the properties of the mortar.

        To ensure that the renovation is successful, the relevant drying conditions according to WTA Code of Practice 2-9-20/D must be met.

        Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.

        When processing in machines, the product-specific data, such as strength, air void content, etc. might change.

    • Working tools / cleaning
      • Mortar cover / Filling knife / Trowel application / Application by spraying
      • Mixer, trowel, smoothing trowel, sponge float

      • Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • Approx. 10.5 kg / cm thick layer / m²
      • Approx. 10.5 kg/m²/cm layer thickness

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • May contain traces of pyrite (iron sulphide).

        Do not use on gypsum-based substrates.

        The mixing water must be of drinking water quality.

        Low chromate content in accordance with Directive 2003/53/EC.

        Always set up a trial area/trial areas first.

        The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

        Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.